Commercial Construction Orlando Advantages Of Using Foam Concrete In Construction |
Posted: January 31, 2021 |
The technology of laying the foundations is known to many and at first glance it seems simple. However, many nuances are often omitted due to ignorance or lack of understanding of the importance of their observance. As a result, these errors occur when pouring the foundation, which leads to irreversible consequences. Even the thin cracks in the walls, overlapping and in themselves are proof of these mistakes and the beginning of the destruction of the house. Technology violation at the design stageEven in the design phase of a building, soil composition, groundwater level, depth and degree of soil swelling must be taken into account. It is also important to know in advance the weight of the future building, including the weight of the base and foundation. The first common errors occur when independently calculating the depth and width of a base, regardless of its type. If the total weight of the house is greater than the maximum permissible load, negative consequences cannot be ruled out. In the reinforcement phaseIn the reinforcement phase, errors in the placement of bars and their arrangement in the corners most often occur. For the most popular tape base, the frame assembly must meet the following conditions: 3 sets of fittings need to be created in each levelThe upper level is at a depth of 5 cm from the edge of the excavation At the corners, the ends of the bars must be bent at an angle of 90°. When building jobsIn addition to these errors, there are also the basics of porches, verandas and other extensions. They are often tied to bases without installation equipment. The nafundamente.ru website explains in detail the technology of casting foundations of any type for houses and various buildings. Here we will notice only such a rule: the reasons for the extension of the building should be independent. When pouring the solutionThe following errors most often occur when pouring out the solution:Insufficient sealing of the mixture. Use a concrete vibrator to fill the prepared trenches with solution. It thickens the mixture and thus increases its strength, water resistance, frost resistance. It should be noted that concrete vibrators are divided into deep, external and superficial. Curing concrete too fast. In hot weather, to prevent rapid evaporation of water, the poured solution is coated with a film for 3-5 days after shrinkage. It is desirable to fill in all reasons to avoid the presence of seams. If this is not possible and the filling is carried out in layers, solidification of the previous layer should be expected. This is because the severity of the next layer can lead to microcracks in the previous layer. As a result, its strength and integrity are compromised. Advantages of using foam concrete in commercial construction OrlandoFoam concrete is a universal, lightweight building material that is ideal for a wide range of commercial construction Orlando work. It can have a density of 400 kg / m3 to 1600 kg / m3 and its resistance to compression ranges from 1 MPa to 15 MPa. To obtain ready-to-use foam concrete, the special foam is mixed with sand, cement, ash and water. The amount of each of these components is regulated depending on the area of final application, balance, productivity and cost. Foam concrete is easy to apply by pouring and does not require compaction, vibration or leveling. Foam concrete blocks are produced in any size according to the order. Depending on the requirements of the architectural project, you can order any volume of individual products. For large and medium-sized buildings, the solution is usually delivered in a huge mixer on a truck. For minor work, the contractor can prepare the material on site. If necessary, it is possible to buy foam concrete blocks in the finished mold. Concrete blocks are a very useful material for the implementation of almost all buildings for several reasons: * foam concrete does not require sealing; * the blocks are relatively light, which minimizes the load on the entire building structure; * in the liquid state it has excellent fluidity, therefore it is quickly distributed on the surface and effectively fills all voids; * the material has excellent load distribution properties; * they do not require maintenance after installation of the unit; * such walls have excellent sound insulation and high heat capacity; * the material is frost-resistant; * they have low water absorption, therefore they are durable; * the material has a high level of fire resistance. Environmental benefitsFluidized concrete saves the use of other materials, because the main component of its production is ash - a by-product of energy production. Due to the fact that foam concrete is light and does not represent a great burden on construction, the construction of large residential and commercial buildings requires less steel and structural concrete. The most obvious advantage for the environment is the high thermal insulation, which reduces energy consumption during the operation of the building.
|
||||||||||||||||
|